Adhesives

  • MOODY, International Certification, Sistem de Management al calitatii certificat ISO 9001
STANDARD PROFI
STANDARD PROFI
  - Common adhesive for the interior and the exterior, used for fitting ceramic plates.
STANDARD PROFI

Caracteristics

Mineral adhesive mortar based on quartz sand, silica sand, Portland cement, fine aggregates and water-soluble additives. It is used for fitting ceramic plates, such as tiles or glaze, on the inside and the outside, on concrete or screed base layers (minimum M50) or cement coating, having a water absorption degree of 3% - 6%. Surfaces on which STANDARD PROFI is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. The adhesive is prepared by mixing a 25 kg powder sack with 6.2 l (250 ml/kg) of clean and cold water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking the base layer and preparing the paste, the adhesive obtained is applied with the help of a rectangular indented spatula which creates a grooved and uniform surface. The thickness of the layer is determined by the angle of the jointer when applying the product. The applied layer should be between 5 mm and 7 mm thick. The plates applied on the adhesive paste are slightly pressed with the hand and they are lightly hammered with a rubber hammer to eliminate blow holes. Spacers are used for straightening the joints. While fixing the plates on the spread paste, the maximum intervals for carrying out the operations will be rigorously observed. If application takes longer than the mentioned intervals, adherence will be lost. Consumption: between 4 kg/m² and 7 kg/m² depending on the size of the plates.

 
PLUS
PLUS
  - Common adhesive with extended open time, for the interior and the exterior, used for fitting ceramic plates
PLUS

Caracteristics

Mineral adhesive mortar based on siliceous sand, Portland cement, fine aggregates and water-soluble additives. It is used for fitting ceramic plates, such as tiles or glaze, on the inside and the outside, on concrete or screed base layer (minimum M50), cement coating, having a water absorption degree of 3% - 6%, or plaster board layers. Surfaces on which PLUS is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. In case ceramic plates are applied on base layers made from plaster board, it is recommended to prime such layers with HIDROFLEX. The adhesive is prepared by mixing a 25 kg powder sack with 6.2 l (250 ml/kg) of clean and cold water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking the base layer and preparing the paste, the adhesive obtained is applied with the help of a rectangular indented spatula which creates a grooved and uniform surface. The thickness of the layer is determined by the angle of the jointer when applying the product. The applied layer should be between 5 mm and 7 mm thick. The plates applied on the adhesive paste are slightly pressed with the hand and they are lightly hammered with a rubber hammer to eliminate blow holes. Spacers are used for straightening the joints. While fixing the plates on the spread paste, the maximum intervals for carrying out the operations will be rigorously observed. If application takes longer than the mentioned intervals, adherence will be lost. Consumption: between 4 kg/m² and 7 kg/m² depending on the size of the plates.

 
UNIVERSAL
UNIVERSAL
  - Flexible adhesive for the interior and the exterior, used for fitting ceramic plates.
UNIVERSAL

Caracteristics

Mineral adhesive flexible mortar based on siliceous sand, Portland cement, fine aggregates and water-soluble additives. It is used for fitting various plates, such as tiles, glaze, porcelained tiles, on the inside and the outside, on concrete or screed base layer (minimum M50) or cement coating, having a water absorption degree of 3% - 6%. This adhesive is specially conceived for floor coverings, such as porcelained floor tiles, on the inside and the outside, having maximum sizes: 30 - 30 cm. Surfaces on which UNIVERSAL is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. The adhesive is prepared by mixing a 25 kg powder sack with 6.3 l (250 ml/kg) of clean and cold water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking the base layer and preparing the paste, the adhesive obtained is applied with the help of a rectangular indented spatula which creates a grooved and uniform surface. The thickness of the layer is determined by the angle of the jointer when applying the product. The applied layer should be between 5 mm and 7 mm thick. The plates applied on the adhesive paste are slightly pressed with the hand and they are lightly hammered with a rubber hammer to eliminate blow holes. Spacers are used for straightening the joints. While fixing the plates on the spread paste, the maximum intervals for carrying out the operations will be rigorously observed. If application takes longer than the mentioned intervals, adherence will be lost. Consumption: between 4 kg/m² and 7 kg/m² depending on the size of the plates.

 
IDEAL FLEX
IDEAL FLEX
  - Flexible adhesive for the interior and the exterior, used for fitting ceramic plates.
IDEAL FLEX

Caracteristics

Mineral adhesive flexible mortar based on siliceous sand, Portland cement, fine aggregates and water-soluble additives. It is used for fitting various plates, such as tiles, glaze, porcelained tiles, on the inside and the outside, on any type of base layer, yet compatible with cement, and having a water absorption degree of 3% - 6%. Surfaces on which IDEAL FLEX is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. The adhesive is prepared by mixing a 25 kg powder sack with 7 l (280 ml/kg) of clean and cold water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking the base layer and preparing the paste, the adhesive obtained is applied with the help of a rectangular indented spatula which creates a grooved and uniform surface. The thickness of the layer is determined by the angle of the jointer when applying the product. The applied layer should be between 5 mm and 7 mm thick. The plates applied on the adhesive paste are slightly pressed with the hand and they are lightly hammered with a rubber hammer to eliminate blow holes. Spacers are used for straightening the joints. While fixing the plates on the spread paste, the maximum intervals for carrying out the operations will be rigorously observed. If application takes longer than the mentioned intervals, adherence will be lost. Consumption: between 4 kg/m² and 7 kg/m² depending on the size of the plates.

 
Klinker Fix
Klinker Fix
  - Adeziv flexibil pentru interior-exterior, utilizat la fixarea placilor de Klinker.
Klinker Fix

Caracteristics

Se utilizeaza pentru placarea suprafetelor cu caramizi aparente klinker. Suprafetele pe care se utilizeaza KLINKER FIX trebuie sa fie din beton, mortar de tencuiala sau sape minim M50, plane si netede, curate si uscate fara praf si fara fisuri. Prepararea adezivului se face prin amestecarea unui sac de 25 kg pulbere cu 7 litri (280 ml/kg) de apa curata si rece. Dupa amestecare se lasa cca. 10 minute in repaus si se reamesteca 1-2 minute. Dupa reamestecare pasta obtinuta este gata de utilizare. Nerespectarea fazelor de preparare duce implicit la pierderea proprietatilor produsului si poate genera esecuri de utilizare. Dupa verificarea suportului si prepararea pastei, adezivul obtinut va fi intins pe suprafata de placat cu o gletiera cu dinti. De asemenea, se va aplica adeziv si pe spatele placilor tot cu gletiera cu dinti in asa fel incat adezivul sa umple canalele pentru aderenta. Placile se vor fixa la locul lor prin apasare puternica si usoara miscare stanga-dreapta. In urma fixarii nu trebuie sa ramana bule de aer in masa adezivului. Consum: 5 kg/m², in functie de dimensiunea placilor.

 
MARMOFLEX
MARMOFLEX
  - White flexible adhesive, for the interior and the exterior, with extended open time, used for fitting ceramic plates and natural stone coverings
MARMOFLEX

Caracteristics

White mineral adhesive flexible mortar based on siliceous sand, Portland cement, fine aggregates and water-soluble additives. It is used for fitting ceramic plates such as: floor tiles, glaze, porcelained tiles (regardless of sizes), mosaics (even those made from natural stones) and for fitting natural stone coverings, such as: marble, travertine, limestone, granite, both on the inside and on the outside, on any type of base layer, regardless of age, yet compatible with cement and with a degree of water absorption between 3% and 6%. Surfaces on which MARMOFLEX is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. The adhesive is prepared by mixing a 25 kg powder sack with 7 l (280 ml/kg) of clean and cold water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking the base layer and preparing the paste, the adhesive obtained is applied with the help of a rectangular indented spatula which creates a grooved and uniform surface. The thickness of the layer is determined by the angle of the jointer when applying the product. The applied layer should be between 5 mm and 7 mm thick. The plates applied on the adhesive paste are slightly pressed with the hand and they are lightly hammered with a rubber hammer to eliminate blow holes. Spacers are used for straightening the joints. While fixing the plates on the spread paste, the maximum intervals for carrying out the operations will be rigorously observed. If application takes longer than the mentioned intervals, adherence will be lost. Consumption: between 4 kg/m² and 7 kg/m² depending on the size of the plates.

 
GLASSKOL
GLASSKOL
  - Flexible adhesive, for the interior and the exterior, with extended open time, used for fitting ceramic plates, natural stone coverings as well as Nevada-type glass bricks.
GLASSKOL

Caracteristics

Mineral adhesive flexible mortar based on siliceous sand, Portland cement, fine aggregates and water-soluble additives. It is used for fixing ceramic plates, such as: floor tiles, glaze, porcelained tiles, irrespective of their sizes, mosaics (even those made from natural stones) and for applying natural stone coverings such as: marble, travertine, limestone, granite and NEVADA-type glass bricks, both on the inside and on the outside, on any type of base layer, regardless of age, including bituminous membranes, pool walls or plaster board provided that the base layer should be primed with HIDROFLEX for the last three types mentioned. Surfaces on which GLASSKOL is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. The adhesive is prepared by mixing a 25 kg powder sack with 7 l (280 ml/kg) of clean and cold water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking the base layer and preparing the paste, the adhesive obtained is applied with the help of a rectangular indented spatula which creates a grooved and uniform surface. The thickness of the layer is determined by the angle of the jointer when applying the product. The applied layer should be between 5 mm and 7 mm thick. The plates applied on the adhesive paste are slightly pressed with the hand and they are lightly hammered with a rubber hammer to eliminate blow holes. Spacers are used for straightening the joints. While fixing the plates on the spread paste, the maximum intervals for carrying out the operations will be rigorously observed. If application takes longer than the mentioned intervals, adherence will be lost. Consumption: between 4 kg/m² and 7 kg/m² depending on the size of the plates.

 
GLASSKOL ALB
GLASSKOL ALB
  - Adeziv flexibil, de culoare alba, pentru interior-exterior, cu open time extins, utilizat la fixarea placilor ceramice, montajul placarilor din pietre naturale precum si a caramizilor din sticla de tip Nevada
GLASSKOL ALB

Caracteristics

Mortar adeziv mineral de tip flexibil, de culoare alba, pe baza de ciment Portland, nisip cuartos, agregate fine si aditivi hidrosolubili. Se utilizeaza la fixarea placilor ceramice, de tip gresie, faianta, gresie portelanata indiferent de dimensiuni, a mozaicurilor (chiar si a celor din pietre naturale) si la montajul placarilor din pietre naturale de tip marmura, travertin, calcar, granit si a caramizilor de sticla de tip NEVADA atat la interior cat si la exterior, pe orice tip de suport, indiferent de vechime, inclusiv membrane bituminoase, pereti piscine sau carton gipsat cu conditia ca in cazul ultimelor trei, suportul sa fie amorsat cu HIDROFLEX. Suprafetele pe care se utilizeaza GLASSKOL trebuie sa fie din beton, plane si netede, curate si uscate, fara praf si fara fisuri. Pentru prepararea adezivului se amesteca un sac de 25 kg pulbere cu 7 l (280 ml/kg) de apa curata si rece. Dupa amestecare se lasa cca. 10 minute in repaus si se reamesteca 1 - 2 minute. Dupa reamestecare pasta obtinuta este gata de utlizare. Dupa verificarea suportului si prepararea pastei, adezivul obtinut se aplica cu un spaclu dintat de forma dreptunghiulara care creeaza o suprafata striata si uniforma. Grosimea stratului este determinata de inclinatia mistriei la aplicare. Grosimea stratului aplicat trebuie sa fie intre 5 mm si 7 mm. Placile aplicate pe adezivul pasta se preseaza usor cu mana si se bat usor cu un ciocan de guma, pentru a elimina golurile de aer. Se recomanda utilizarea distantierilor pentru alinierea rosturilor. In timpul montajului placilor pe pasta intinsa, se va urmari cu strictete respectarea timpilor maximi de lucrabilitate. Depasirea lor duce la pierderea aderentei. Consum: intre 4 kg/m² - 7 kg/m² in functie de dimensiunea placilor.

 
PLANIFLEX
PLANIFLEX
  - Adeziv de tip flexibil, cu consistenta autonivelanta, cu timp de lucrabilitate mare, care se utilizeaza la lipirea la interior si exterior pe pardoseli a placilor de ceramica si/sau placilor din roci naturale, cu dimensiuni medii sau mari.
PLANIFLEX

Caracteristics

Mortar adeziv mineral de tip flexibil, cu consistenta autonivelanta, pe baza de ciment Portland, nisip cuartos, agregate fine si aditivi hidrosolubili. Se utilizeaza la lipirea la interior si exterior pe pardoseli a placilor de ceramica si/sau placilor din roci naturale de tip marmura, travertin, calcar, cu dimensiuni medii sau mari. Produsul PLANIFLEX se utilizeaza doar pe suprafete orizontale. Suprafetele pe care se utilizeaza PLANIFLEX trebuie sa fie din beton, plane si netede, curate si uscate, fara praf si fara fisuri. Pentru prepararea adezivului se amesteca un sac de 25 kg pulbere cu 6-6,5 l (240 - 260 ml/kg) de apa curata si rece. Dupa amestecare se lasa cca. 10 minute in repaus si se reamesteca 1 - 2 minute. Dupa reamestecare pasta obtinuta este gata de utlizare. Dupa verificarea suportului si prepararea pastei, adezivul obtinut se aplica cu un spaclu dintat cu dantura de forma dreptunghiulara sau semicirculara, care creeaza o suprafata striata si uniforma. Grosimea stratului este determinata de inclinatia mistriei la aplicare. Grosimea stratului aplicat trebuie sa fie intre 3 mm si 20 mm. Placile aplicate pe adezivul pasta se preseaza usor cu mana si se bat usor cu un ciocan de guma, pentru a se asigura acoperirea spatelui placii cu adeziv in proportie de 100%. Se recomanda utilizarea distantierilor pentru alinierea rosturilor. In timpul montajului placilor pe pasta intinsa, se va urmari cu strictete respectarea timpilor maximi de lucrabilitate. Depasirea lor duce la pierderea aderentei. Consum mediu: 5 -7 kg/m2.