Caracteristics

Mineral mortar for preparing the final finishing-type filling mixture, based on Portland cement, quartz sand, silica sand and specific water-soluble additives. CEMENT GLET is used for finishing walls covered with cement-based coating using a masons float. Surfaces on which CEMENT GLET is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free. If the water absorption degree of the base layer exceeds 6%, the layer is primed with Hidroflex. The product is obtained by mixing a 25 kg powder sack with 6.5 l (260 ml/kg) of clean and cold water, only in clean and appropriate containers, until a homogeneous paste is obtained; this is done by pouring the product into the water. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. After checking and eventually preparing the base layer, the obtained paste is applied with the hawk. The applied layer should be between 1 mm and 3 mm thick. If more layers need to be applied, the different layer applications should be carried out at intervals of about 24 hours. Consumption: approx. 1.4 kg / mm/m².

• Download Technical datasheet CEMENT GLET
• Download Fisa tehnica de securitate CEMENT GLET

Caracteristics

Adhesive mortar for autoclave-cured cellular concrete masonry, based on grey cement, quartz sand, silica sand selected inert materials and additives. It is used for fitting autoclave-cured cellular concrete blocks for masonry works. The autoclave-cured cellular concrete blocks on which mortar is applied should be clean, dry, dust free and should not contain non-adhesive substances; they should be well lined up so that the maximum distances of adhesive mortar layer between the blocks should not exceed 3 mm. The mortar is obtained by mixing a 25 kg powder sack with 6 l (240 ml/kg) of clean and cold water, only in clean and appropriate containers, until a homogeneous paste is obtained; this is done by pouring the product into the water. Mixing is carried out for about 4 minutes in order to obtain a perfectly homogeneous paste. After mixing, the paste is left to rest for about 10 minutes, then it is mixed again for about 1 - 2 minutes. After that, the obtained paste is ready for use. The resulted paste is applied with an indented spatula (tooth size: 6mm). After its application, the autoclave-cured cellular concrete block is immediately pressed so that the layer should be 3 mm thick after this operation. Consumption: approx. 30 kg/m³.

• Download Fisa tehnica de securitate B.C.A. FIX
• Download Technical datasheet B.C.A. FIX

Caracteristics

Mineral mortar based on Portland cement, selected aggregates and water-soluble additives. AUTOLIV CLASIC is used for the fine levelling of floors with a view to creating a base layer with technical characteristics appropriate for final floor coverings such as: PVC, carpet, laminated or veneered floor coverings, multi-layer parquet, parquet, epoxy coatings, polyurethane coatings etc. Surfaces on which the self-levelling screed is applied should be made out of concrete, should be flat and smooth, clean and dry, dust and crack free, resistant, compact and with no brittle parts. After checking the layer on which AUTOLIV CLASIC is to be applied, the person responsible with the application rigorously vacuums the surface of this layer and applies the appropriate primer with a brush or a painting roller: Primer L 2022 for absorbent surfaces, and Primer L 7012 for non-absorbent surfaces. From priming up to the application of the self-levelling screed, attention should be paid so that the primed surface should be kept clean and dust free. The paste results from mixing a 25 kg sack of AUTOLIV CLASIC with 5.5 l - 6.5 l (220 - 260 ml/kg) of clean and cold water, only in clean and appropriate containers, until a homogeneous paste is obtained. After mixing, the paste is left to rest for about 10 minutes and then it is mixed again for about 1-2 minutes, and then it is immediately poured. It is recommended to pour the mixture quasicontinuously, with an interval between the pouring operations of about 3 - 4 minutes. The minimum thickness of an applied layer is of 2 mm, while the maximum thickness is of 4-5 mm. For higher values, successive layers will be poured at 48 hour intervals, each layer being primed. A thickness of 10 mm is allowed, on certain areas of maximum 4 cm provided that the distance between such areas is of at least 1 mm. After applying the product on the base layer, the former is immediately levelled with a levelling board (masons float, hawk) made from stainless steel. After levelling, air is eliminated from the applied paste with a rubber or plastic needle roller. Consumption: approx. 1.7 kg/m²/mm of thickness.

• Download Fisa tehnica de securitate autoliv clasic
• Download Technical datasheet AUTOLIV CLASIC

Caracteristics

Se utilizeaza pentru nivelarea si egalizarea sapelor de sulfat de calciu, ciment, asfalt turnat, magnezit, sapelor cu uscare rapida, cat si pentru nivelarea straturilor de sapa la cladiri vechi, in vederea constituirii unui suport cu caracteristici tehnice adecvate pentru pardoseli finale din PVC, mocheta, parchet, placaje ceramice, pardoseli laminate sau furniruite, parchet multistrat, etc. AUTOLIV PIANO 4 poate fi utilizat si pentru pardoseli incalzite. Suprafetele pe care se aplica sapa autonivelanta trebuie sa fie plane, netede, curate, uscate, fara fisuri, lipsite de parti friabile si substante neaderente. Dupa verificarea suportului pe care se aplica AUTOLIV PIANO 4 aplicatorul va aspira foarte bine suprafata suportului si va aplica cu pensula sau cu trafaletul grundul adecvat: PRIMER G 2022 pentru suprafete absorbante, respective PRIMER G 7012 pentru suprafete neabsorbante. Se va urmari ca de la grunduire si pana la aplicarea sapei autonivelante, suprafata grunduita san u se murdareasca sau sa se prafuiasca. Pentru prepararea produsului, se amesteca un sac de 25 kg AUTOLIV PIANO 4 cu 6 l (240 ml/kg) de apa curate si rece, doar in recipiente curate si adecvate pana la obtinerea unei paste omogene. Dupa amestecare, sapa autonivelanta se lasa cca. 10 minute in repaus, dupa care se reamesteca un minut. Dupa reamestecare, sapa se toarna imediat. Sapa autonivelanta proaspat amestecata se toarna pe suportul verificat si amorsat in prealabil si se niveleaza cu un dreptar (drisca, fier de glet) din inox de minim 50 cm lungime, pana la nivelul dorit. Operatiunile de nivelare cu dreptarul si scoatere a aerului se vor face de catre aplicator intr-un interval de maxim 4 - 5 minute de la turnare si folosind saboti cu cuie in cazul in care este necesara calcarea peste sapa proaspat turnata. Grosimea minima a unui strat turnat este de 1 mm, iar grosimea maxima este de 20 mm. Pentru obtinerea unor grosimi mai mari, se vor turna straturi successive de sapa, la un interval de 48 de ore, cu amorsarea fiecarui strat. Sapa autonivelanta proaspat turnata se protejeaza de uscarea prea rapida, de conditii termice extreme, inghet si aer uscat. O uscare prea rapida poate conduce la aparitia fisurilor. Temperaturile mai ridicate si umiditatea scazuta a aerului accelereaza uscarea, iar temperaturile scazute si umiditatea ridicata a aerului, intarzie uscarea. Consum: cca. 1,5 kg/m²/mm grosime.

• Download Technical datasheet AUTOLIV PIANO 4

Caracteristics

PRIMER L 2022 is a primer which reduces the degree of absorption of the base layer on which the self-levelling screed AUTOLIV CLASIC is applied (see AUTOLIV CLASIC data sheet). Before applying the product, the base layer should be vacuumed and clean, dust and salt free, with no non-adhesive substances (grease, bitumen, dust, gypsum, dye, old wall painting etc.); it should have a neutral pH, be resistant, compact, non-crumbly, with no brittle parts and no cracks. If a base layer is not compatible with AUTOLIV CLSIC (see AUTOLIV CLASIC data sheet), then, neither priming with PRIMER L 2022 will help make it compatible. Priming is done by applying the product with the brush, the masons brush or the painting roller on the base layer checked as mentioned above; the self-levelling screed AUTOLIV CLASIC is to be applied on this base layer. After priming, the surface should be kept clean and dust free until the application of the self-levelling screed. The surface should not be forcedly dried by ventilation or high temperatures. Depending on the degree of absorption of the base layer, the priming procedure is performed as follows:

a. For medium absorbent surfaces (for example: initial layer of self-levelling screed, concrete, finely mashed off mortar screed), PRIMER L 2022, diluted with clean and cold water (1:1 ratio), is applied; this is done approx. 120 minutes before applying the auto-levelling screed.

b. For absorbent surfaces (for example: screed approx. M100, old or new), priming is done in two stages, as follows:

a. First, PRIMER L 2022 is abundantly applied, diluted with cold and clean water at a 1:4 ratio, then it is left to rest for about 120 minutes;

b. Secondly, PRIMER L 2022 is applied, diluted with cold and clean water at a 1:1 ratio; this operation is done approx. 120 minutes before applying the self-levelling screed.

• Download Technical datasheet PRIMER L 2022
• Download Fisa tehnica de securitate PRIMER L 2022

Caracteristics

PRIMER L-7012 is a primer for nonabsorbent or lightly absorbent surfaces (mosaic, floor tiles etc) on which the self-levelling screed AUTOLIV CLASIC is applied (see AUTOLIV CLASIC data sheet). If a base layer is not compatible with AUTOLIV CLASIC (see AUTOLIV CLASIC data sheet), then, neither priming with PRIMER L-2022 will help make it compatible. Priming is done by applying the undiluted PRIMER L-7012, with the help of a brush, on the base layer (checked and cleaned as mentioned above) on which the self-levelling screed AUTOLIV is to be applied. The primer shall be evenly spread on the entire area on which AUTOLIV CLASICis going to be applied. The self-levelling screed shall be applied 24 hours after performing the priming procedure. The surface on which the self-levelling screed is to be applied should be evenly covered with primer, should be kept clean and dust free until the application of the respective screed. The surface should not be forcedly dried by ventilation or high temperatures.

• Download Technical datasheet PRIMER L 7012
• Download Fisa tehnica de securitate PRIMER L-7012

Caracteristics

Primer G 2022 is an blue ground for absorbent surfaces (concrete, light concrete) on which the self-leveling compound AUTOLIV PIANO 4 has to be applied. The grounding is carried out by applying the product in non-diluted state. The support has to be stable, smooth, dry, non-iced, clean, without traces of dust, rubble, oils or fats, without traces of release agents. The applying of the product is done by brush or roller. After grounding, till the applying of self-leveling compound, the surface will be protected against dust or dirt. It is to avoid the forced drying by ventilation or increasing of temperature. After drying, the self-leveling compound can be applied.

• Download Technical datasheet PRIMER G 2022

Caracteristics

Primer G 7012 is an yellow ground for the inside and outside applications, used at restoration , to be applied on old and nonabsorbent supports. The support on which the product will be applied must be stable, smooth, dry, non-iced, clean, without traces of dust , rubble, oils or fats, without traces of release agents. The applying of the product is done by brush or roller. After grounding, till the applying of self-leveling compound, the surface will be protected against dust or dirt. The product can be applied after the ground is dry and does not stick.

• Download Technical datasheet PRIMER G - 7012